How to repair a laminate with your own hands

Laminate coating is particularly wear -resistant. However, when exposed to the laminate of mechanical damage, scratches, cracks, chips can form on it. These problems most often arise if the installation technology of this material has previously been violated. We learn about how to repair a laminate with your own hands and save it from all kinds of defects.

Table of contents:

1. In the laminate a hole - how to repair
2. How to repair a laminate: chip or scratch
3. How to repair the floor from a laminate with your own hands
4. How to repair a laminate swelling from water
5. How to repair the floor from the laminate yourself: getting rid of the divergence of joints
6. How to repair laminate - scuffs and surface defects

In the laminate a hole - how to repair

In order to determine the procedure for restoring the laminate, it is necessary to study the nature of the damage. If there is an overly large hole or defect on the board, it is best to replace it. In the process of replacing the board, perform the following actions:

• If the board is extreme, then with its extraction problems will not arise, disassemble a certain section of the floor, replace the board and collect it back;
• If you fail to get to the board with a defect, then in this case, it is removed using a wrapping, for this, using a circular saw, the board is cut into several parts that are easily removed from the floor;
• Be careful when performing cuts, the circular saw should be configured to a certain thickness, thus it will be possible to maintain the substrate under the board of the whole and unharmed;
• Use a regular chisel to cut the thickness;
• Take a new board and cut the keyhole on its surface, show special accuracy to avoid damage to the front surface on the laminate;
• Install a new board in place by fixing it with the help of liquid nails, for uniform installation of the board, put a heavy object on it;
• Wipe the excess glue with a dry rag.

Thus, in the presence of a hole on the surface of the hole, it is enough to drill a damaged area with a saw, and install a new board.

In order to complete the cut of the laminate without damage, adhere to such recommendations:

• make markings on the daughter on both sides so that she coincides with each other;
• The painting tape installed around the perimeter will prevent laminate coating with cracks;
• In the ratio with the marking line, cut the floor with a cutter;
• Using an electric jigsaw, saw a coating at an angle of thirty degrees.

The laminated floor is characterized by good performance and stability before surface wear. The cost of this coating is much lower than the price of parquet, but at the same time, holding a certain technology for laying the laminate and certain rules of its operation, it is possible to maintain this coating in ideal form.

In order to avoid the appearance of scratches and chips on the laminate, do not drop sharp and heavy objects on it. It is not recommended to walk on a laminate in high -heeled shoes or with a rough sole. To walk on the laminate, use soft indoor slippers.

Furniture, which is installed in the room should be equipped with soft substrates. Thus, in the process of its movement, small scratches and chips will not form.

How to repair a laminate: chip or scratch

If there are chips, deep cracks or cracks on the surface of the laminate, it is necessary to close them using special compositions. To carry out the repair of chips on a laminate surface, use the following methods:

• a mixture for the preparation of which is used gypsum, sawdust, water, proportions of adding one to one, while a thick paste should be obtained, which fills the cracks well;
• Smole on a polyester or epoxy also allows you to get rid of various defects of the laminate surface;
• mastic for working with wooden surfaces allows you to save the laminate from chips;
• Another reliable option is acrylic sealant.

When buying mastic or sealants, choose two color options at once - dark and light, in this case, you can easily choose a shade in a ratio with the flooring. Keep in mind that the drying field, the resulting composition will change the color in the dark. In the process of working with the compositions, show maximum caution, put on gloves and apply a mixture with a rubber spatula. In order to get a positive effect of one bullying, it is most often necessary to apply the paste several times to the surface.

If there are minor damage in the form of scratches on the surface of the laminate, then use wax pencils to remove them. There are two types of these tools:

• hard;
• soft.

With the help of soft restoration wax, it is possible to quickly and efficiently close all the cracks and scratches on the floor, which is exposed to high operational loads. While hard wax is used for the floor with medium or low loads to the surface. With the help of soft wax, cracks are sealed in the damaged area of \u200b\u200bthe laminate.

Before starting the laminate with a wax pencil, it is necessary to carefully study the instructions for its operation.

How to repair the floor from a laminate with your own hands

To restore the appearance of the laminate coating, you need to familiarize yourself with the instructions that will help to do this. If there are too deep scratches, it is necessary to replace damaged boards.

There are certain repair kits with which the surface restoration passes quickly, and the floor, after restoration, has an attractive appearance. Most often, chips and scratches on the laminate floor are eliminated using wax pencils or special pastes.

To mask scratches on the floor, use a special repair kit that matches the color of the coating. In the process, the availability of:

• spatulas of different configurations;
• Venika;
• repair kit.

In order to close up a small crack on the floor, you will need about fifteen minutes. A special composition is applied to the surface. Next, you should wait until it dries and remove excess, if necessary.

The use of a wax small is also an effective way to remove scratches. Choose a chalk in a ratio with the color of your flooring. To cleanse scratches, use a vacuum cleaner, then with a pencil, lay out the defect. Using dry fabric, remove excess wax and polish the surface. In the presence of too deep scratches, fill them with a putty.

In order to close cracks and chips by putty, perform the following actions:

1. Take a laminate board and select a repair kit in the store, suitable in color for your sex.

2. To apply the paste, use the spatula, use the unnecessary part of the laminate for training. To remove an excess of pasta, use a clean rag. Wait for the complete drying of the pasta and polish the surface, if necessary.

Thus, answering the question of how to repair a dent laminate, it is best to use a special repair paste for these purposes.

How to repair a laminate swelling from water

Vimitation of the laminate is a rather frequent process, which can cause various causes, such as:

• Water shedding on the floor;
• low quality of material;
• The lack of a gap between the walls and the laminate.

To determine the cause of the laminate, carefully inspect the surface. If the coating has a wave -shaped shape, then errors were made in the process of its installation. Inspect the outer panels, a compensation gap should be present between them and the wall.

The second reason is to get the liquid on the floor, in this case, the laminate absorbs the liquid and swells under its influence. If the bloating of the laminate is determined by the low quality of the material, then in this case, it is necessary to dismantle the coating and install a new laminate.

In other cases, it will still be possible to restore the floor. The first reason is the ingress of liquid to the floor surface. Keep in mind that in order to avoid swelling of the laminate under the influence of moisture, it is recommended to apply special waxes or polishes with a moisture -repellent effect to its surface.

If the laminate nevertheless swollen, then first of all, dismantle the damaged panels and inspect them. If the material is not cheap, then wait for its drying. High -quality laminate, does not lose its shape, and does not deform under the influence of moisture.

If after dismantling the coating you find water under the boards, then remove it. Thus, the coating will not have time to absorb moisture, and will not lose its shape.

If a lot of time has passed after moisture enters the laminate, then in this case, swollen panels must be replaced. Keep in mind that if the laminate was laid several years ago, then it will not be possible to completely guess its color. In this case, we recommend using the panel from under the cabinet or bed, and in its place to install a new material that is clearly distinguished against the background of the coating.

If, performing installation work, the gap between the laminate and the wall is absent, then there is also a risk of coating deformation. When resting the laminate into the wall, it is necessary to cut it off in these places. With a wave -like bloating of the laminate, remove the barriers that interfere with the coating in a completely horizontal position.

Instructions on how to repair a swollen laminate:

• dismantle the plinth;
• With the help of a pencil, it should be noted the location of the laminate with the wall;
• The protruding areas are cut, note that the skirting boards should close the gap at the place of its connection to the wall.

The gap between the pipes and the laminate should be the same as the distance from the laminate to the wall.

In order for the laminate not to be covered with waves, and does not swell, first of all observe the technology of its proper styling. Choosing a laminate, it is better to give preference to its qualitative options. Periodically process the floor with waterproof compounds that will help prevent the harmful effects of moisture on the material.

How to repair the floor from the laminate yourself: getting rid of the divergence of joints

In case of violation of the installation technology of laminate coating or as a result of exposure to the temperature fluctuations laminate, joints form between the panels. These gaps negatively affect the appearance of the coating and lead to its stratification. In addition, water entering the surface of such a laminate leads to a quick spoilage. In order to prevent this trouble, it is necessary to adhere to a certain technology for mounting the laminate.

First of all, before the start of installation work, the laminate must acclimatize in the room. It is for this reason that there are quite often gaps between the boards. Bring the laminate into the room, at least two days before the start of its installation.

In addition, the coating, before starting installation work, should be particularly evened. Only in this case, the laminate will last you as long as possible. In order to check the flatness of the floor before laying the laminate, use the alcohol level. To eliminate micronerings on the floor, install a screed with self -leveling characteristics.

In any case, before starting work, the surface for laying the laminate should be qualitatively leveled. Observing these recommendations, the cracks and joints will not form between the laminate plates, leading to a decrease in its operation.

How to repair laminate - scuffs and surface defects

The answer to the question is whether it is possible to repair the laminate on which there are scuffs, definitely yes. If, for any reason, scuffs appeared on the laminate, then several methods will help to get rid of them.

The first method is the use of special paint for laminate. When choosing its color, we recommend that one board of the laminate take with you to the store. This paint is available in a small container, easily applied to the surface, quickly dries and gives the laminate of shine. After using such paint, the coating acquires its former attractiveness. Also, this paint allows you to get rid of not only scuffs, but also from small scratches.

The second option is the use of a polish for a laminate. There are two options for polishes:

• a product that has a liquid base;
• viscous compositions.

In order to improve the clutch between the polishes and the laminate, the composition of these compositions contain additional substances. The use of a polish allows you to perform the following actions:

• increased juiciness and brightness of color;
• elimination of scuffs and small scratches;
• Creating a brilliant and clean layer that is held for a long time.

Laminate polishing is performed several times for a year. Thus, the maximum effect of its effects is achieved. Two main methods for applying polishes are distinguished:

1. A less expensive option. Dilution of water polishes with water. Wipe with this composition of the floor. This polishing method resembles wet cleaning. The addition of water is carried out in relation to the instructions. The duration of the protection of such a polish is quite low.

2. The second option for applying polishes involves the use of sprays and mastic. It is the spray that allows you to distribute the composition on the floor surface. Follow the absence of fluxes on the floor.

For dense mastics, small -car fabric is used. This polish does not need its frequent use and retains its effect for a long time.