Repair and replacement of a plastic window handle yourself

Plastic windows are not such simple products as it might seem. All provisions of the sash are controlled with the help of just one pen, which transfers efforts to numerous gear ratio mechanisms of accessories. It is not sacred that the first of the plastic window is the first to get out of the system, because it is constantly twitching, turning, twisting. But problems can be immediately after installing windows, if they are not accurately adjusted or have a factory marriage. Although there may be other reasons. If you install plastic windows in compliance with all technologies and nuances, and then carefully operate them, then they can last many years without the need for repair. But if, nevertheless, the handle for the plastic window broke, or it jammed in any position, or it does not turn, or does not turn to the end, then do not despair, it is possible to eliminate such a problem yourself. In this article, we will talk about how to make out the handle of the plastic window, how to adjust it, repair or replace it with a new one without resorting to the help of specialists. To do this, you will need straight arms, the keyhine key is M-shaped 4 mm, a cross-shaped screwdriver and a smart head on the shoulders.

1. The handle of the plastic window in the position is closed, and the window sash does not close
2. The handle of the plastic window does not turn or does not turn until the end
3. The handle of the plastic window was ill
4. The handle broke on the plastic window replacement of the handle
5. Choosing a handle to plastic windows

The handle of the plastic window in the position is closed, and the window sash does not close

It is possible that you have encountered such a problem of the window handle is in a position that does not correspond to the position of the sash, and it is impossible to turn the handle jammed it. For example, the sash can be open, and the handle in the position is closed. You were just about to close the window, but it doesn’t work, since it is impossible to crank the handle. What to do? First of all, you should not very tug in the handle, this will not bring a positive result. The reason for jamming the handle of the plastic window is that it worked out of time block.

Almost all modern windows are equipped with a special lock, which blocks the handle turning. This is done with the good goal so that you inadvertently break the window. When you turn the handle in a folding position (the handle looks up) or in the rotary (the handle is located horizontally), the lock is triggered and the handle prevents involuntary turning. It happens that the lock is cut untimely. Most often, this happens if you translate the position of the handle too fast. How to repair a plastic window handle in this case? First of all, it is necessary to determine the manufacturer of accessories, this will depend on the method of disconnecting the lock.

The name of the fittings can be viewed on any metal part of the window. This is easy to do if the sash is in the open position. Most often, the name is just in the area of \u200b\u200bthe handle, on the end part of the sash.

If you have an Aubi accessories: To disconnect the sulfur lock, it should be in an upright position. If it is in a rotary-oatmeal position, then the lock located on the upper loop will also prevent the handle. Therefore, we transfer the sash to a vertical position, then in the area of \u200b\u200bthe handle on the end part of the sash we find a plate with a spring. It must be pressed to the sealant, and then turn the handle in a position inherent in the sash.

If you have accessories Maco, Roto, Gu, Winkhaus: Also in the area of \u200b\u200bthe handle on the sash we find a metal plate, which is not vertically located, but is at an angle to the frame and sash. It must be pressed so that it becomes parallel to the frame, i.e. Strictly vertical, then turn the handle to the right position.

If, when trying to close the window, you still do not turn the handle, then you should check if the lock with a response mechanism is in contact. A situation is possible when the lock skips past without clinging to the mechanism. The reason is the temperature expansion.

If you notice that the lock is slipping, then you need to open the sash, find the response mechanism, unscrew the screws with which it is screwed to the frame, then remove it, put something between it and the frame and screw it into place. As a lining, you can use a piece of non -weed plastic. As a result, the response mechanism should be located further from the frame, and the lock should be hooked for it. Try to close the window again. If it turns out, the repair is over.

The nuances of the winkhaus accessories: Some models of windows with this fittings are equipped only with a blocking, located on the scissors of the rotary-oatmeal mechanism. In the process of work, this blocker wears out as a result of constant friction, so over time it may fail. This is characterized by the fact that the handle can only be turned into a position openly (horizontal) or in a rotary-oxide position, to ventilate (the handle up). In such a situation, you can not try to close the window and turn the handle, making great efforts. The gearbox of the main constipation may break. This is the case when it is better to entrust the repair to professionals, especially if the windows are still under warranty. If you intend to solve the problem yourself, you will have to remove the window sash.

On the upper loop of the sash, it is necessary to remove the decorative pad, then pull out the pin holding the sash in the frame. For this, a screwdriver and pliers are used. Gently remove the sash from the loops, put it on the floor and remove the scissors. To remove scissors, unscrew the screws with which they are fixed. Remove the lock and install the scissors back.

If all of the above procedures did not help, do not zeal, consult professionals.

The handle of the plastic window does not turn or does not turn until the end

The problem of a different property is when the handle of the plastic window does not close, when trying to close the window, the handle does not turn to the end. At the same time, if the window is open and try to turn the handle to the position closed, after turning off/pressing the lock, then the handle turns easily. There may be two reasons for such a problem.

First the lubricant in accessories dried up. As already mentioned, the work of the window is provided by many gear ratio, so their movement should be light and smooth. If the lubricant in the accessories has dried up, or dirt fell into it, then her work is broken. If the reason is only in grease, then the repair of the plastic window handle can be performed independently. To do this, you will need a lubricant: either universal lubricant, or a special lubricant for plastic windows, or, in extreme cases, a WD-40 lubricant will fit.

It must be poured into all movable elements of accessories, this can be done through holes, including in the upper part of the accessories. Then it is necessary to turn the handle in one position, then to another, so the accessories will move and distribute grease along its surface. If the reason is only in grease, then this should be enough. If the reason in the mud that has hilled under the fittings, then it is better to invite the masters, since you will have to remove all the accessories from the window and rinse it in a special bath.

The second slowing the sash. This can be an imperceptibly naked eye, but even one millimeter will be enough so that the handle is not transferred to the position closed.

The position of the sash is up and down can be changed using adjusting screws. It is necessary to remove the decorative plug from the lower sash of the plastic window. In the upper part of the loop mechanism there is a hole for the hexagon of the hexagon by 4 mm.

We insert the G-shaped key into the adjusting groove and turn it. If you turn clockwise, then the sash will rise, if you sink against the hourly. Each time, making several turns, we try to close the sash. In some types of accessories, the adjusting groove is located on the front surface of the loop (as in the photo).

The sash can also be adjusted in a horizontal position to the left-right. Typically, the upper and lower part of the sash are adjusted separately.

The lower part is using the lower loop. If you open the sash and look at the side surface of the lower loop, then the adjusting groove will also be noticeable on it. We insert a hexagon into it for 5 mm and turn into it. Clockwise the sash moves left, against the clock to the right.

The upper part of the sash is regulated by the mechanism, which is located on the sash at the top. To adjust the sash, it is also necessary to open, almost wide open. Almost at the top of the very top will be an adjusting groove. We insert a hexagon into it and turn it.

The handle of the plastic window was ill

It happens that the handle of a plastic window was simply ill. She scrolls into all positions, but nothing changes. The reason, most likely, is that the fastening of the handle is ill, and the handle mechanism does not hook with the mechanism of accessories. This problem is solved very easily.

The plastic window handle is adjusted using two screws with which it is screwed to the sash. On the sash directly under the handle there is a decorative element of the plug (rectangular in shape). It is necessary to gently pry it with your hands, pulling it over, and then turn 90 degrees. Those. The plug must be placed horizontally.

Two fasteners of the handle, the other from below, will appear to your attention. They must be twisted with a cross screwdriver.

The handle broke on the plastic window replacement of the handle

This situation is rare, but still it happens: the handle can crack, break out or just come into unusable from old age. In this case, you will need to replace the handle on the plastic window. There is another reason to change the native pen, even if it is in good condition, the need to install a pen with a lock. When there are small children in the house and parents want to make it so that the child could not open the window or door to the balcony himself, special hands with locks are installed.

To remove the handle from the plastic window, it is necessary to unscrew those two screws that were discussed above. But first you need to open the sash so that the handle is in the position openly. After the screws are unscrewed, you need to remove them and then gently remove the handle.

You can buy a new pen on the construction market or in the construction supermarket, as well as in the company that is engaged in the production of plastic windows. In addition to ordinary pens, you can purchase a pen with a lock and even a comb that limits the window opening.

The handle is installed on the plastic window using the same screws that they kept the previous one, although you can use new ones. If you plan to install the opening limiter, then we insert the regulator plate (comb) into the base of the handle. Then the pin of the handle is inserted into the hole, and the handle itself is screwed with screws.

Choosing a handle to plastic windows

Handles for plastic windows produce not only the same companies as accessories. For example, you can buy a handle of production of China, Turkey, Austria, Germany, Great Britain, Poland and other countries. Window handles for plastic windows are considered, as it were, consumables, they can differ in shape, but necessarily universal and approach all window models and all accessories. The material of the manufacture of aluminum, the most common color is white, but the handles can be under a tree, gold or bronze. So you can choose the color of the windows. The shape can be rectangular, rounded, and with recesses for the fingers.

On the handle for a plastic window, the price practically does not depend on the shape, only on the quality and manufacturer, as well as on the color (not white handles are more expensive). For example, the Chinese pen will cost only 2.5 cu, Turkish in 8.7 cu, German and Austrian in 10 cu The price of a handle from the UK depends on the form and varies in the range of 12 15 cu. A separate category is pens for plastic windows with locks: Polish will cost 25 cu, and the same analogue from the UK of 36 38 cu

Repair or replacement of a plastic window pen one of the lightest tasks in the repair of plastic windows. This does not require qualification or additional knowledge. The main thing is not to panic and follow the above instructions. If the above tips do not help, then be sure to call the master so that he can see the problem with your own eyes.