Very often, the desire to increase the living space of the house comes to naught because of ...
Very often, the desire to increase the living space of the house comes to naught because of ... |
The labycle grid is widely used both in construction and in landscape design ... |
The simplest structure near the country house or at the cottage of an additional ... |
All modern kitchen sets have hinged cabinets in their configuration. They allow saving space with good capacity. Located at the eye level, such cabinets are very convenient during operation and are always filled with a large number of things, creating a serious load on hinged mechanisms. Therefore, it is very important to produce a reliable and high -quality fastener of the cabinet to the wall.
Misractors:
Before starting mounting hinged cabinets to the wall, you need to choose the right height for their hitch. It is determined based on the main criterion - the growth of the owner of the kitchen. On average, the distance is approximately 50-60 cm from the countertop to the lower part of the hinged cabinets. According to GOST, this value is generated 45 cm.
In the case when to place the hinged cabinets is required above the refrigerator or above a high oven, then the height of these objects determines the desired level of hinging cabinets.
The use of modern fastener fittings greatly simplifies the work that is associated with a hitch of kitchen cabinets. It allows you to eliminate small errors in applying the marking and increases the strength of the entire structure. At the same time, there will be very little effort, and all the work can be done independently, without any help.
For attaching the cabinet to the wall, a specially prepared rail and a device called a hitch is mainly used.
The weight is equipped with crocheted, which is attached from the inside to the side wall of the cabinet and remains invisible from the side.
The first way is a hitch on the mounting bar.
Advantages of this method:
Flaws:
The second method is more affordable, but will take more time, in addition, additional help will be required. It will use loops and fasteners.
Initially, the upper boundary is determined and the horizontal line is applied along the length of all the cabinets that need to be suspended.
Then, the level of its setting is determined by the level (there are cases when, due to the uneven sex, the result is distorted).
The first point is marked on the resulting line, a hole is made using a perforator or drill, and fasteners are installed. Then the cabinet is taken, and temporarily suspended in order to determine the place of the next fastener with absolute accuracy. In this case, one should not be guided by one drawn line, but even the evenness of the cabinet itself must be checked by the level.
The entire further process is carried out in the same way. When all the cabinets are attached and their location is checked by the level, you can start connecting them with furniture screws among themselves. The final stage of work is the installation of a connecting decorative cornice, which is screwed to the upper base using screws.
Now it remains only to hang the facades, install the shelves, see whether the doors work normally, and if there is a need to adjust the inaccuracies using the adjusting screws. This whole process requires concentration and good attention, as well as an insightful assistant, without the help of which it is quite difficult to correctly calculate the required distance for fasteners.
The course of work on the hitch will directly depend on the design of the posterior wall of the hinged cabinets.
In the first case, the back wall is nailed to nails and has no recesses. Therefore, when hung on the mounting bar, the upper part will not fit tightly, and the cabinet will turn out with a slope. In order to avoid this, a waste should be provided at the bottom of the cabinet, which corresponds to the width of the mounting bar. To do this, you can nail a thin rail or calculate the height of its hitch so that it enters the kitchen apron. In the latter case, the fasteners should be carried out already with the installed kitchen apron.
In the second case, the back wall is attached to the recess.
This design of hinged cabinets is more convenient, as it allows them to be hung not only in the overlap on the kitchen apron, but also in the water. But when installing cabinets without overflow, it is important that the apron is located perfectly evenly, since even a small skew will immediately catch your eye.
In order to highlight the kitchen cabinets at hand, you need to have the following tools:
First of all, using adjusting screws, it is necessary to fix the hooks in the middle position. After that they are attached from the inside on the side walls so that the hook peeps out by only 2-3 millimeters and can freely cling to the fastener.
Now you can start applying marking on the wall. In this case, one should be guided by the basic rules:
Taking into account all these recommendations, using the level, two lines are applied, starting from the corner of the kitchen. Of these, one feature shows the upper edge of the hinged rail, and the second indicates the top of the cabinets.
Tip: In order to determine the horizontal position of the cabinets, it is best to use the level, rather than measuring the distance from the ceiling or floor, since subsequently errors may occur. Even if there is confidence that the ceiling or floor is quite smooth, you should not take risks, otherwise you will have to redo all the work again.
The upper edge of the bar is pressed to the prepared marking line (lower) and the required number of marks for openings for fastening is made.
If the walls are durable and have a good bearing ability, then it is quite possible to divide the rail into small pieces of 15 cm, and each of them should be installed in those places where the awnings will be located. But if there are at least the slightest doubts about the strength of the walls, you should not divide the rail, but on the contrary, more steadily to fix it for a larger number of fasteners.
Further, a drill of a certain diameter, a small hole for installing the rail is carefully made in the wall. The following will be set out several basic recommendations:
Then, dowels are neatly driven into the holes, and the mounting rail is installed on the fasteners. On it, with the help of a hitch, cabinets are attached. Their position is regulated by the screws with which the hinged mechanisms are equipped.
To create the effect of the cabinet throughout the wall, you need to tightly connect them to each other. To do this, they need to be fixed in pairs in clamps, starting from the corner cabinet. In order not to spoil their surface, you should put a wooden wedge between the cabinet and the clamp.
Next, a hole between the connected cabinets is drilled under the intersection screed. With through drilling on chipboard, chips are often formed.
To prevent this problem, it will be necessary to apply one of two of the following methods:
On this fastening of the hinged cabinets is finished, it remains only to install the shelves, fix the doors and adjust them with the help of the screws that are on the hinges.
Very useful article!
Very useful article! Thanks a lot!
I'm shocked! I cook the kitchen to
I'm shocked! I am preparing the kitchen for installing furniture ... It turned out that the wall between the kitchen and the toilet is 4 centimeters !!! What to do? How to hang cabinets?
Where to find this master?
Where to find this master? mirhar@mail.ru
Thank you! I'm not a handle, house
Thank you! I am not a handle, I built the house myself. Accordingly, I make the kitchen myself. Your advice has helped. Thanks again!
Aunt in the video full
Aunt in the video is complete inadequate! It was necessary to control the kitchen so as a hysteria! "I do not know how you can do it, I don’t know, but do it!"
Thank you, conceived a custom
Thank you, conceived a custom cuisine, it was not the first day that the network was in search of how to avoid distortion when attaching to the mounting bar (for the corner kitchen is critical), perhaps for many this is obvious, but my first time is the first time;) everything is very clear and informative Spastbo again!
The article was written by a full profan.
The article was written by a full profan.
evaluates \u003d equals
evaluates \u003d equals
Nonsense at the end of the work of the master,
Delirium at the end of the work of the master, he was too lazy to put the door to put on the door, he is obliged to do work to the end. When your wife begins to cook, and then he says to the end, you yourself cook, but if he suddenly produces the brains, so here. Nonsense master, nizachot.
All characters are full.
All characters are full. One hysteria, the other itself cannot, the third if you undertook to correct, then there is nothing to listen to those who do not think. In general, it was necessary to hang 8mm with a hexagonal header on a dowel. Izh Planet hung on a wall on two dowels of 20mm for almost a year.
And which dowel screwed like this
And what dowel screwed up and said
thanks for the advice useful
thanks for the advice, useful article
Thank you very much! The best article
Thank you very much! The best article on this topic. All the nuances are taken into account. It is your reason that the professional wrote.