DIY LED backlight

When you make the apartment repair completely yourself, you can easily cope with such a creative process as creating a unique LED backlight. How to make LED backlight yourself, is it possible and how simple such questions arise in front of you. Due to the fact that now they make stretch ceilings made of drywall - the installation of LED backlighting has become possible in any apartment, as well as in any part of it: a bedroom, a kitchen or a bathroom. You can even install it in the closet.

What is LED

What is the LED tape or LED tape is a flexible bar, on the one hand having an adhesive base, and LEDs and resistors are located on the other. The tape has multiple areas (5 cm), on which three LEDs and special marks are most often located, indicating where the tape can be cut. LEDs in the tape are connected by a sequential chain. The ribbons can be protected from environmental influences with plastic tubes or silicone, and can be open, depending on their place of use, the tape is also selected. There are two types of diodes used in the tape: SMD 3528 and 5060 (5050), the latter are more powerful and can be used as independent sources of room lighting.

If you use RGB tape for backlighting, it is important to know that it has four exits - for the bulk and one for each color: red, green and blue.

Scheme of LED backlight

If you need to light a large area, then it is better to make tapes not more than 15 meters long, otherwise the lamps are closest to the power source will faster, since at the beginning of the circuit the voltage will be very strong.

The order of your actions:

You determine the type of SMD 3528 or SMD 5050 LED will be more expensive, but their power is higher.

We determine the desired density of the LEDs. There are 30, 60, 120. The indicated number shows the number of LEDs by one meter, the larger the number, the brighter the lighting will be.

We are determined with the type of tape. For example, IP 44 is moisture -proof. We determine with the adhesive side you need it or not.
The color is one color or multi -color, for the second you need a controller.

Counts: We measure the perimeter of the site where the backlight will be located, calculate the total area - we multiply the consumed power of one meter by the resulting meter. According to the received data, we select a power supply and controller.
We determine the option of the backlight. There will be protrusions from drywall or not to decide.

Installation: cut the tape (there are special marks on it - where you can cut), we solder single -color areas like K +, for a multi -colored tape, we solder the same areas with the letter designation V +, R, G, B. Remember that connect to one block Nutrition can be no more than 15 meters of tape.
Connection. We check the polarity of errors should not be! If the network cord is not connected in advance, then connect the cord to the L and N contacts, then if you have a multi -color tape, we connect the controller and only then connect the tape directly.

Most often, the contour lighting of the ceiling is used, but other options are possible. With the help of LED lamps and ribbons, you can favorably distinguish between parts of the room or emphasize the color scheme of the room. For example, if your bedroom is made in blue deep colors, then the ceiling can be decorated with a pattern of LED lamps so that it will seem like a starry sky above your head. If two children live in the children's room, then the light separation of the room is an interesting solution so that each child has its own corner for work and for sleeping.

The advantages of LED LED illumination are that it is easily mounted, is relatively inexpensive, it serves for a long time and it has different colors. Whereas standard luminous household appliances only two options are warm and cold. And if we talk about Neon, then he is short -lived, composed in the installation.

The colors of the colors in LED lamps are diverse - from one -color, to RGB tape, which can change color. If you do not have strong restrictions on money, then buy a full -color tape and a separate controller for it. When buying a tape, choose in silicone isolation, if you are flooded by neighbors from above, then the wiring will be safe. As for the choice of a particular color, you decide: for the eyes, green color is more pleasant, but blue can be perceived incorrectly, sometimes even dull.

The backlight can be performed by different options, it can be LED lighting of the stretch ceiling, using a hard module, point lamps, as well as mini -floodlights, can be used. What your fantasy will be better to use from this, or maybe a comprehensive solution to all family members, because everyone wants to rebuild the world around him, and even more so. The main task when installing backlighting it should be inconspicuous from below, therefore, in order to hide it, ledges or cornices are used, while the distance also matters. So with a too long distance - the backlight will illuminate the niche itself than the ceiling directly, and with the small, the diodes and the gaps between them will be noticeable, which are not covered.

The illumination of LED ribbon is easier both in installation and in the functionality of it can be installed where other lamps can not cope. For the tape, even hard -to -reach places are not a hindrance.

LED light lighting

First you will need to create a design project, that is, a work plan and a drawing of the final result. It is important to correctly calculate how many lamps are needed, in which specific places to place them, how many meters of LED tape you need, it is important to remember that it is more convenient to take a multiple of 5 cm tape - at this distance you can place 3 LEDs. Then, after calculations, you need to buy LED backlight, power supply to it, and if you buy a multi -color tape, then the controller for it. When everything is bought, be sure to read the instructions. For ease of installation of LED backlight, on one of its sides there is an adhesive layer. Previously, the mounting location must be cleaned and treated with an alcohol solution. Then remove the protective layer press the tape to the mounting site and hold a little. If your tape according to the project should bend, then remember, excesses should be more than 2 centimeters in diameter.

Depending on the country of the manufacturer, on the diodes used, as well as on color, the price of LED backlight will differ.

LED backlighting kitchen

LED backlighting in the kitchen is already becoming very fashionable and popular, with its help you can designate different areas, create coziness or intimate atmosphere for a pleasant evening. Using LEDs in the kitchen, you can illuminate niches, apron, cabinets above or below. Currently, such a backlight is used in bars, restaurants, as well as in hotels.

If you want to divide the space into working and the rest in the kitchen, use different colors. For wooden furniture, it is better for you to use diodes of warm shades of yellow and orange, if you have a high-tech kitchen, then blue or silver colors will suit you more. And the guests reception zone can be equipped with a full -color ribbon with a controller.

You can also beautifully highlight a bar rack or a glass cabinet with crystal will look just great and gorgeous.

Lighting in the car

One of the last innovations for the car is the installation of LED tapes on it. At the same time, the car itself is illuminated from below, the lightning of the cabin or the LED lighting of the instrument panel is made. Today, LED bulbs are sold in a large assortment, installed in the dashboard, they consume little energy and at the same time quite bright. Since there are more and more identical machines in the parking lot, you will help to make your car unique from the rest and will help equip it with LEDs. You can tunen your car both using LED lamps and with LED strips. An unusual solution may be the backlight of the car's discs. The blue diodes are traditionally used, but you can choose another color, depending on the color of your car.

LED panels backlighting

In addition to LED strips, there are also LED panels, as a rule, they are very thin (about 13-15 cm), have a variety of colors and dimensions. This novelty attracts the attention of designers, as it allows you to solve such problems as, for example, too low ceilings. Or, if you need a bright color scheme for the walls here the panel will simply help out, while the ribbons will be lost. This is a great solution for a children's room, and for a restaurant, and for a club atmosphere, they can be used in office and storage facilities.

LED panels are designed for different use, they are also developed for installation to concrete and brick walls or ceilings, can be built into a suspended ceiling, or can be separately suspended by special mounts.

You can not worry about vision of the light panels are absolutely safe for your eyes. As a rule, light panels have different light intensity, which can be adjusted using a special remote control.

LED devices lighting from lamps and spotlights, to panels and ribbons, is modern, stylish and non -standard. With the help of such lamps, you will make the design of your apartment or office, or an unforgettable and unique car. You can use LED lamps for the improvement of various landscapes in hotel design, entertainment parks or even in the pool. You can install them both independently and by inviting specialists. In addition to beauty, LED lighting lighting consumes much less electricity, are high -tech and reliable products.

Site search

Table of contents