Partial dismantling of laminate with your own hands

The duration of the operation of the laminate is from 10 to 20 years, depending on its type and class. However, there are situations when there is a need to restore the laminate by partial dismantling. In order not to damage the coating, it is necessary to strictly adhere to the technology of dismantling the laminate. We will consider how to dismantle a laminate with your own hands.

Parquet dismantling - laminate laying

In some cases, during the repair, the laminate is laid directly on the parquet. However, if the condition of the parquet is bad, then it is much cheaper to dismantle it, align the draft floor and install the laminate.

If the condition of the parquet is good, then the laminate is laid directly on it. By laying a laminate over the parquet, pay attention to such technological nuances:

1. Do not lay the laminate in one direction. This styling method will not allow creating a solid and aesthetically attractive surface. The method and manner of laying the laminate depend on the individual characteristics of the room. To hide the boundaries of the transition, use special species or finishing accessories.

2. If there are voids in the floor, they must be eliminated. Otherwise, setting a laminate on this place, there is a likelihood of damage. To eliminate voids, use wooden strips, which are also used to strengthen the shaken elements.

3. The most common problem after installing the laminate is the appearance of creaks while walking along it. The problem of the creaking of the laminate indicates the incorrect work.

Before starting work, it is necessary to check for strength. To remove the recesses, use wood putty. In order to get rid of the creak, drill a hole between the strips and set it inside its wood spike.

The surface should be even, the maximum changes in height are 20-30 mm. Next, you should cover the surface of the draft floor after the primer dries, the substrate is laid on the floor, the type of which is determined by the operational load of the coating.

The process of laying on the surface of the parquet is performed in the same way as on the usual floor. The panels are laid in a parallel position in relation to the sun. This styling method is the most preferable. Do not forget about the indentation from the wall, the optimal value of which is 15 mm. The method of connecting the panels determines further actions. Laminate laying is performed in relation to the instructions from the manufacturer and in compliance with all technological aspects specified in it.

Features of installation of laminate dismantling

The cause of partial dismantling of the laminate is most often defects that occur on its surface, as a result of exposure to the laminate of mechanical factors or spilling various kinds of liquids. In some cases, the use of wax pencils or a special composition for repair work is enough to restore the laminate.

However, if chips or cracks on the laminate are serious, it is more advisable to replace the damaged panel. Dismantling of the laminate should be performed so that the panels, after removing them from the floor, could be used a second time.

The reasons for dismantling the laminate are:

Technologically incorrect installation of panels, the result of such actions is the occurrence of a creak during walking;
bloating and deformation of the boards, after the influence of moisture on them;
When moving, a laminate is possible and installed in new housing.

There are situations when certain laminate panels are damaged, in which case they are replaced by new ones. However, if the laying of the material has been done for a long time, then new boards, against the background of the old floor, will be noticeably different. In this case, it is recommended to dismantle the boards located under the cabinet or other furniture, and install new boards on them. Dismantled panels are installed at the site of worn parts of the laminate.

Dismantling of a laminate is a rather complicated process, however, if you approach it technologically correctly, then performing it yourself will not be difficult. In the process of performing work, show special accuracy and accurate movements, especially if a partial replacement of the laminate is performed.

To properly carry out the dismantling of the laminate, first of all, determine the type of connection of the panels. There are three options for panels, in relation to the method of their connection:

1. adhesive compounds - in this case, the panels simply glue with each other. This version of the laminate is not subject to partial dismantling.

2. A castle laminate - on the one hand on the panel is a spike connection, and on the other - a groove connection. Thus, the stud part, after tapping it, drives into the groove. After a characteristic click, the panels are connected to each other.

3. Click click is the most popular connection system. With its help, the assembly and disassembly of the laminate is not difficult. The installation of one panel to another at an angle of forty -five degrees allows you to connect them together. Next, the panel drops to the floor, connecting to the rest of the panels.

DIY Laminate dismantling

For the correct dismantling of spoiled boards using a marker or other item, indicate the place of work. Using an electric jigsaw, saw a damaged panel, retreat from its edge at least half a centimeter, in order to avoid damage to the castle connection. Using tools, remove the canvas. Build the preparation of the panels, clean its edges, apply a sealant on it and install it in the place of the extracted board. Use a dry rag to remove sealant.

Please note that the finished board must be selected in the ratio with the color and size of the laminate. At the same time, the panel, which is installed on the surface should be 3 mm less than the extracted in size.

In order to replace several boards on the floor, it is necessary to initially dismantle the skirting board. Next, the extreme panel is raised, which disconnects the keyboard system. Gradually disassemble the laminate until you get to damaged areas.

To complete the complete dismantling of the coating, the presence of:

tools for dismantling the coating;
vacuum holders;
hammer;
chisels;
screwdriver;
pencil or marker.

Using a screwdriver, dismantle the baseboard around the perimeter of the room. The first panel is dismantled by removing it through the surface of the heat clearance. To discrepancy the connection, raise the panel. Keep in mind that all movements should differ in smoothness and caution. When removing each panel, apply a license plate with a pencil to install the laminate in the same sequence back.

It is necessary to disassemble the laminate from the site where its installation ended. Most often, this is a door or a window. Thus, the full dismantling of the laminate is performed.

How much is the dismantling of the laminate - the price of the service

The installation of laminate dismantling the cost is affected by the nature of the work. Separately, the fate is necessary for the dismantling of the skirting board. How much is the dismantling of a laminate per square meter depends on the type of work:

dismantling the laminate without its preservation;
dismantling of a key laminate with the further use of the material;
Laminate connection type;
The total area of \u200b\u200bwork.

The price per m2 depends on the quality of the coating itself, its class, such as a connection, the need to maintain a laminate, etc. The average cost of dismantling the laminate while maintaining the coating is 170 p. per square meter.

Having completed this work yourself, you will be able to save good money. However, for this it is necessary to stock up on patience, time and a certain tool.

Dismantling of a laminate from the center

Keep in mind that the laminate is allowed to dismantle a maximum of three times. Since the key system of this material is particularly fragility and is destroyed in the process of dismantling. Since the floor replacement is a rather expensive process, it is enough, if there is damage, replace a certain panel.

In the process of working on the dismantling of the laminate, it is enough to prepare a pencil and a screwdriver. In addition, the presence of an electric jigsaw, chisel, rubber spatula, jigsaw, etc. will be required.

First of all, you should start with the dismantling of the plinth. In this matter, it is necessary to determine its type. If the baseboard has a hole for the channel cable, then it is fixed using self -tapping screws and dowels. To extract them, use a screwdriver. Initially, all the plugs should be dismantled, under which self -tapping screws are located. Disconnect the baseboard and put it aside. If the location of the baseboard was carried out using liquid nails, then for its dismantling it is necessary to use a hammer and a chisel. In this case, the baseboard is not subject to further use.

Keep in mind that a laminate board with a key connection is laid in compliance with a gap of one and a half centimeter. It is with the help of this cunning that it is possible to easily dismantle the laminate, if necessary.

Keep in mind that in the presence of a defective bar, it is enough to change it with a laminate bar located under a cabinet or bed. Thus, it will be possible to easily restore the coating, while saving, at the same time, on the selection and purchase of a new laminate bar.

Before starting work, inspect the floor for a gap between the wall and the laminate. If there is no gap, then it will not be possible to dismantle the first board without damage. Using a jigsaw, cut the extreme part of the laminate located against the wall.

Rapin the locking connection, then lift and press the laminate using the screwdriver. Pull out the first panel after a click indicating that there was a division. All lamellas need to be numbered. We recommend folding the panels in three separate piles, the first on the right side, the second central, and the third overlap laminate on the left side.

Do not overdo it with pressure on the laminate, as there is a risk of damage. Panels in which castle elements were damaged are laid on glue.

Features of the dismantling of laminate with aluminum compounds

The laminate, the connection of which is carried out with the help of aluminum brackets, withstands several cycles of installation and dismantling. The floorboards are distinguished by the presence of built -in aluminum plates protruding for each panel.

The lower part of such a coating is characterized by the presence of adhesive shock -absorbing substrate. To disassemble such a laminate, it is necessary to work hard. Since the compound is a sidon-fraud, while the lamellas are interconnected quite firmly. Add a special bracket and a sludge made of wood to a standard set of tools.

To replace the lamella, located in the central part of the room, set the bracket into the end seam, hitting it with the help of kiyanka, remove one of the rows a few centimeters to the wall.

To release the panel, set the bracket into the longitudinal seam, with the help of a kiyanka, remove the laminate located next to it. Next, you should disconnect the damaged panels and replace them with new ones. After installing the panel, you need to take care of its compaction. To do this, with the help of a kiyanka, tap on the bracket, waiting for a characteristic click. The remaining actions are performed as well as when dismantling the panel.

If glue was used as the main fixing laminate of the substance, then in this case, the procedure for dismantling the floorboards changes. To extract the laminate, it is necessary to cut it.

Follow the instructions below:

Using a marker, circle damaged areas of the laminate;
using a grinder, cut off damaged panels;
Using the chisel, Paturate the cut part and remove the laminate;
Using a wooden bracket or kiyanka, remove the laminate for 15 mm to the wall;
dismantle the remaining parts of the damaged laminate;
To clean up the joints of the laminate, use the chisel;
Apply sealant or laminate glue to the new panel;
fix the suction cup on the board;
The second suction cup is attached to the lamel adjacent to the damaged board;
Using the suction cup, install the floorboards and fix them in the right position;
Try to avoid the appearance of gaps between the panels;
To remove excess glue, use a rubber spatula.

After the glue is completely dried, the coating is ready for operation. This option of dismantling the laminate is not particularly laborious and quite easy to perform. With it, it is possible to dismantle the laminate located in any part of the room.

Dismantling the video:

Site search